EFVM Leak Detection Services

The ASTM [American Standards Testing Method] we have mentioned above are internationally recognized standards and are also recognized in the Australian standards as we do not currently have our own standard for ELD testin


The final type of ELD tesƟng listed in the ASTM D7877 guide is the low voltage horizontal membrane scanning plaƞorm. This can be a time-consuming process if the original waterproof membrane applicator is not on site to rectify any detected faults immediately. Detected breaches will need to be repaired before further testing can be carried out. Two probes are used to identify breaches and will always be directed to the strongest breach.
AS 4654.1: Waterproofing Membranes for External Above Ground Use Testi


Australian Laboratory Services (ALS) was founded in 1976 in Brisbane, Australia, providing laboratory testing, inspection, certification, and verification solutions to a wide range of products and industries, including toys, nursery, general merchandises, electronics, and soft lines. As a Public Health Laboratory NATA accreditation is critical to our business providing confidence to our clients that all processes are audited to a documented quality assurance program. Recognition as a NATA accredited laboratory facilitates business opportunities by providing recognition that the organisation delivers high quality pathology services. Industry-leading non-destructive testing, material analysis, and inspection services to ensure the integrity and safety of your assets. UL’s facilities in Australia and New Zealand provide compliance solutions and lab testing services in accordance with the universal bi-national AS/NZS standard system, covering most of the consumer commodities and industrie


Low AS/NZS 4858 Wet Area Waterproofing Membrane Testing Voltage Field Vector Mapping involves a perimeter wire being installed around the area to be tested. Seams on sheet membranes are also difficult for this method to accurately test as the thickness at the seam is doubled; high voltage current cannot travel laterally through a seam defect. It requires a direct air gap under the brush to the conductive substrate to spark.
AS ISO 13007.5 and AS ISO 13007.6 – Waterproof Membranes for use beneath ceramic tiling bonded with adhesives
AS/NZS 4858 sets out performance and general test requirements for waterproof membranes, specifically those defined in AS 3740 including liquid and sheet membranes. Clause F2D2 and Specification 26 of Volume One of the NCC sets out the areas that must be waterproof or water resistant for Class 2 to 9 buildings. Waterstop termination for unenclosed showers must be flush, with the finished floor level and at the perimeter of the shower are


Revolutionizing the building inspection industry, making it safer, faster, and more cost effective. Timely routine inspections on membranes helps to ensure the best out AS/NZS 4858 Wet Area Waterproofing Membrane Testing of the membrane system in place. Adhesion testing is an important method of evaluating the bond strength of a waterproofing membrane to its substrate.
Membrane application and correct terminati


TREMseal Bandage is a TPE flexible sealing tape, is thin and extra-tough elastic strip with considerable longitudinal and lateral extension. TREMproof Torch 4000M is a 4mm thick, APP modified bituminous torch applied waterproofing membrane which is polyester spunbond, with glass filament reinforcement. TREMproof 260 is a polymer-enhanced, single component, fluid-applied, bitumen emulsion, waterproofing membrane.
Tremco Xylol
TREMproof Torch Bitumen Primer is a solvent based modified bitumen primer designed to assist with adhesion of the TREMproof Torch and TREMproof 560A membranes to the substrate. TREMproof 250GC is a rapid curing, high solids, low VOC, moisture cure modified polyurethane waterproofing membrane that can be applied to "Green" (24 hour old) concrete. Polyurethane membranes cure to form an elastic waterproof seal that is free of seams to prevent moisture or water to leach into the surface. Cementitious waterproofing membrane has great adhesion to concrete, cement rendered masonry and fibre-cement sheet, and provides a uniform colour and texture similar to mortar. Vulkem NEM Plus is an Australian made single component, moisture curing, high tensile strength and tough curing polyurethane membran

However, not all ELD testing equipment can find breaches on vertical substrates, multiple horizontal breaches in a single test or test semi-conductive coatings – i.e. membranes such as Black EDPM, Black Butynol or polyurethanes tinted with Carbon blac


Safe Environments is actively involved in slip resistance research presenting at the International Ergonomics Society, Slips Trips and Falls Group and contributes to Australian Standards Committee BD-094 Slip Resistance of Flooring Surfaces and the UK Slip Resistance Group. As every property is different, we take the time to customise our service to your specific requirements We are a family-owned national company, who have been working in the slip prevention industry since 2004 Whether you need wet pendulum testing, on-site slip resistance measurements (AS 4663), or lab testing to AS 4586, our expert technicians deliver accurate, fast, and fully certified reports. Providing frequent scheduled services to both capital and regional areas throughout Australia, we offer services in any location at highly competitive rates. Additionally, our Global Product Classification service AS/NZS 4858 Wet Area Waterproofing Membrane Testing specialises in determining the suitability of pedestrian surface products prior to installation and during constructio